Instructions To Solve Canon Printer Error

Canon printers can print pages up to the point where the ink absorber has reached its limit. Canon printer error 5b00 can occur when the waste ink absorber is full. This error code will appear on the LED display if ink spills onto the printer.

Sometimes the main reason for this error can be found in the dirty waste ink absorber. canon 5b00 error This issue can cause you to not receive the desired print result.

We are here to help you overcome this technical problem.

Fix Canon Printer Error 5B00 With 4 Simple Methods

Use the solutions provided to solve the problem.

Solution 1: Use Service Mode

Let’s begin with the basics of troubleshooting. It is recommended that you turn off your Canon printer first. After waiting for a while, turn the printer on again. Check the status code.

If the Canon printer is not working, you will need to restart it. Next, set the Canon printer’s Service Mode.

For the task to be completed, press and hold the Power button for between 5-10 seconds. Release the Power button after that.

Next, press the Zoom button 5-6 times. If the LED lights are on twice, the Canon printer has entered the Service Mode. Move to the Control Panel to confirm that Service Mode is active.

Scroll down and tap the “Devices and Printers” option in the Control Panel. You will see the Printer Status set to Offline. This indicates that the Service Mode has been enabled.

Check if the error code was removed. If the error code is still present, proceed to the next step.

Solution 2: Verify the Ink Level

This issue can sometimes be caused by the ink system installed. Here are some steps to eliminate it.

First, unplug your printer. If you are using a USB cable to connect the printer to your computer, you must also unplug the USB cable. You must also press and hold the Power button. The next step is to plug in the power cable into the power socket.

Continue pressing the Power button until your Canon printer resets itself automatically. When all lights are on and the Canon printer is making no sounds, you must release the Power button.

Wait until the green power lamp turns off. You will need to press and hold the Power button twice. The green light will now blink for approximately 2 to 3 seconds, and then it will stabilize.

Then, restart your computer and your Canon printer. This should resolve the problem. Here’s another solution if that fails.

Solution 3: Clean the Ink Waste Manually

To manually clean the Waste Ink you will need to first open the Canon printer’s lid and remove the ink cartridges. You will now see a small box, similar to a foam pad, just near the roller.

Use a soft towel to press the foam. The ink will then be released. The foam must be cleaned until all inks are removed. Next, insert the cartridges into the slot.

Close the printer lid. Once you are done, turn on your Canon printer. Turn off your Canon printer. After a few seconds, turn the printer back on.

Solution 4: Use Canon Service Tool Program

First, download and install the Canon Service Tools program. Navigate to the EEPROM tab.

Tap on the EEPROM status before you start the resetting process. This will prompt you to provide the paper source tray. It defaults to be set to the rear tray. Click on it to display the message “A function was completed”.

Tap on the Main option. Next, tap the Settings icon. The printer reset procedure will begin. The resetting process may take some time so be patient.

The LED lights will continue to flash when the resetting process begins. The LED lights will stop blinking when the reset procedure is complete.

Tap again on the EEPROM status to select the EEPROM Save option. The EEROM will then return to 0%, and the issue will be fixed.

Most Frequently Asked Questions

1. What should you do if a “Printer in Error State” message appears on the display?

If you see the message “Printer in error” on your display, make sure that the printer is on and connected to the computer. You should also ensure that the paper is not jammed in the input tray.

2. How do I reset the Canon Printer Ink Absorber

In the beginning, make sure that your Canon printer is off. For a few seconds, hold down the Resume button. Continue holding the Resume button, and then press the Power button.

The green light will begin blinking. Hold the Power button down and release the Resume button. Next, double-press the Resume button. Next, release the Power button. Next, press the Resume button four more times and then again press the Power button. The printer will now be reset.